Skip navigation

Tag Archives: Fuel cell

There is a great deal of misconception about desalination of seawater and the word ‘desalination’ is taken literally as a method of separating  fresh water from seawater but not the separation of salt from seawater. The main focus here is only about recovery of fresh water from seawater or from any saline water sources but not salt. In fact separation of salt from seawater is also known as desalination or desalting. The reason for this misconception is because fresh drinking water is in demand and people are concerned only with fresh water and not the salt. There is a huge demand for fresh drinking water all over the world. Increasing population, large scale usage of fresh water by industries, pollution of fresh water by domestic and industrial effluents, failure of monsoon or seasonal rains due to climate change are some of the factors that contributes to water shortage. There is also a demand for water by agriculture industry both in terms of quality and quantity. Bulk of the ground water is used as a main source of fresh water by agriculture industries in many countries.

But sea water also contains number of minerals or salts which have greater economic and commercial value. In terms of quantity their presence is small, only 3.5% and the rest 96.5% is fresh water. For example Chemical industries such as Caustic soda and Soda ash plants use salt as their raw material. But they also use de-ionized water to dissolve salt to produce brine which is their feed stock.

Therefore Chemical plants are the largest users of seawater in terms of salt as well as fresh water. Power plants mainly located on seashore also use large quantity of de-ionized or desalinated water for boilers and for cooling towers.

Sea is now becoming a great source of fresh water as the inland water supply is becoming scarcer due to dwindling water table by drought or flooding by too much rains, pollution by industries etc. In earlier days seawater was the only source of common salt known as Sodium chloride produced by solar evaporation. Bulk of the salt is till used by this method. Therefore it is logical to locate a chemical plant and a power plant side by side so that seawater can be utilized efficiently.

CEWT (Australian company) has developed a new desalination technology called ‘CAPZ desalination technology’ that can generate fresh water as well as Sodium chloride brine simultaneously which is suitable for Caustic soda/Soda ash production. They can integrate such a facility with a skid mounted Chlorine plant of smaller capacities. This plant can generate large volume of drinking water (WHO standard) as a by-product that can be supplied to municipalities and agriculture industries.

Locating large scale solar salt pans near such a facility will be a problem because it requires a huge area of arid land with good wind velocity and it takes nearly a year to harvest the salt.

Using CAPZ desalination technology one can generate saturated Sodium chloride brine of 315 gpl concentration as well as fresh drinking water directly from seawater. The brine is purified to meet the specifications required by membrane Electrolysis for the production of Caustic Soda. The same brine can also be used for the production of Soda ash using Solvay process.

It is no longer necessary to produce brine from solar salt. Solar salt requires vast area of arid land with good wind velocity and least rain fall and large manual labour force to work under harsh conditions; it is a very slow process and takes almost a year to harvest the salt, which is full of impurities and requires elaborate purification process during the production of Caustic Soda. Such purification process generates huge volume of solid waste for disposal. Chlor-alkali industry is one of the most polluting industries in the world. In fact these impurities can be converted into more value added products such as recovery of Magnesium metal or recovery of Potassium salts. CAPZ technology is developing a ZLD (zero liquid discharge) desalination process where the effluent containing the above impurities such as Calcium, Magnesium and Sulphates are converted into value added products. By recovering more such salts from seawater one can recover additional fresh water. Therefore desalination of sea water is now emerging as an integral part of Chlor-alkali industry. By such integration Chlor-alkali can become a major player is meeting fresh drinking water of a nation.

skid mounted Chlorine plantSkid mounted Cl2 planElectrolysis plant by Thyssen krupBy careful integration and co-location of a desalination plant, Caustic soda plant, Food and pharmaceutical grade salt plant and a power plant  on a sea shore will be a win situation for everybody involved.

Let us take a specific case study of setting up a Caustic soda plant, a captive power plant and a desalination facility.

A typical skid mounted Chlorine plant will have the following configuration:

Capacity of Caustic Soda: 50.7 Mt/day (100% basis)

Capacity of Chlorine        : 45.00 Mt/day (100% basis)

Hydrogen production        : 14,800m3/day (100% basis)

A typical usage of Vacuum salt for such skid mounted Chlorine plant will be about 76.50 Mt/day with a power consumption of 2.29 Mwhr/Mt of NaOH (100%).

A captive power plant of capacity 200Mw will be able to supply necessary power for both Desalination facility as well as Caustic soda plant.

The CAPZ desalination facility can supply a saturated sodium chloride brine (315gpl concentration) 245 Mt/day and 9122 m3/day of fresh drinking water from the desalination plant. This water can be used for boiler feed in the power plant. Surplus water can be supplied as drinking water meeting WHO specifications.

The Hydrogen gas the by-product from caustic soda plant with capacity of 14,800 m3/day can be used to generate clean power using a Fuel cell. The power generated from Fuel cell will be about 20 Mwhr/day that can be supplemented for the Caustic soda production thereby reducing the power consumption from 2.29Mwhr to 1.46 Mwhr/Mt of NaOH (100%)

By careful integration of a large (ZLD) desalination facility with caustic soda plant and power plant it will be possible in future to generate a clean energy using Hydrogen, a by-product of Caustic soda plant and solar thermal plant to produce chemicals in a clean and environmentally sustainable manner.

For further information on CAPZ technology, please contact ahilan@clean-energy-water-tech.com.

 

 

 

“The intuitive mind is a sacred gift and the rational mind is a faithful servant.We have created a society  that honors the servant and has forgotten the gift” – Albert Einstein.

United Nation’s panel on climate change (IPCC) recently confirmed that climate change is real, it is man-made and it is irreversible and if nations do not act now then they will have to face catastrophic climate events in the future. They were categorical and unequivocal in their statements this time. They have come to this conclusion because science has not demonstrated how to   capture carbon emission and sequester them under the earth using current technologies. Scientists neglected carbon emissions while generating power using fossil fuels for decades because they had no idea what would be the consequences of such emissions in the future. It is a clear example how a human mind has a limited capacity to conceive an idea “holistically” but has a capacity to satisfy human needs temporarily without knowing the unforeseeable consequences. When human beings interfere with Nature in the name of Science there are consequences to face and a price to pay because Nature is nothing but the manifestation of the highest intelligence. A real science can be no further than asserting this truth. Ignorance when combined with greed can be a deadly combination and the consequences will be costly and to be paid dearly by generations to come. Carbon emission and climate change is one such issue. Science has improved human life on earth in so many ways but at the same time they also have created many side effects which can be identified only after decades of their use. When they are identified it is often too late and causes irreversible damage to system or nature. Any irreversible change human beings cause in Nature will have its own consequences. Science has shown Carbon is the backbone of all organic matter on planet earth whether it is DNA of a human being or a glittering diamond from deep under the earth. The same Carbon reveals the age of a skeleton of a Dinosaur  buried millions of years ago. Science is a powerful tool but it also has two sides, benign and malign. The power to discriminate between the good and bad is the fundamental pre-requisite of science. Carbon plays an indispensible role in the natural world due to its unique atomic structure and ease with which it can build molecules especially with hydrogen. That is why hydrocarbon is playing such an important role in human civilization and it is not easy to substitute it with another candidate without a long term research and development work. But we have a very short time to discover a substitute for hydrocarbon which can serve our current purposes. Few nuclear power plants around the world can satisfy the growing demand for the electricity without any carbon emission but their long term consequences are unknown. The result of a thermo-nuclear explosion over Hiroshima and Nagasaki are the grim reminder of such consequences. When earth converts organic matter into a fossil over a period of millions of years deep under the earth, it gives us a clue why Nature has buried them and not left them on the surface of the earth. But that did not deter human beings from digging them out and burning them to generate heat to meet their temporary energy needs without realizing the long term consequences of such actions. Many technologies have become obsolete over a period of time for various reasons but some of them lingered long enough to create long lasting consequences and there are many evidences in history to emphasize this truth. Power generation using fossil fuel is one such clear example of a technological bungle. It only confirms the inadequacy of human knowledge.  It also reveals the temporary nature of such inventions stemming from temporary nature of human life. Science also has changed dramatically in the last few decades and it no longer serves the original purpose of unraveling and understanding the mysteries of Nature but caters and serves to the greed and dominance of selected rich and powerful people and the nations in the world. Science has become a tool to create material wealth and power rather than to understand nature and apply them into our lives in a compatible way and to enrich human life. These experiences have taught one important lesson. Any scientific discovery when applied in real life must be “holistic” and be compatible with Nature and should follow Natural laws. When science becomes a wealth creating tool then any knowledge born out of such science can only serve to create wealth often at the cost of Nature. That is why rich and powerful corporate and nations spend billions of dollars in such wealth creating discoveries rather than on discoveries that address human problems of the world that may not return their investment in time. The anomaly is more they invest on wealth creating science more damage they cause to earth and human life. Such discoveries serve only one purpose namely “the wealth creation “. Wealth and power has overtaken science and knowledge. Climate change has become a serious issue and it is absolutely clear that CO2 in the atmosphere has increased to the current level for the first time in millions of years and human beings have contributed greatly to this increase. Yet, nations around the world are unable to come to-gather and agree on how to reduce such emissions. The only way to solve this issue is to use Science as a tool which created this problem in the first place. When steam engine was invented it was considered as the dawn of industrial revolution: when electricity generation using electro-magnetism was invented it was hailed as a land mark in scientific development. When power was generated using fossil fuel to accelerate the industrial growth very little attention was paid to the carbon emission. When huge quantities of sea water was used to cool the cooling towers in fossil fuel powered or nuclear power plants very little attention was paid to the discharge of effluent in to the sea. When large desalination plants were set up to quench the thirst of oil rich countries very little attention was paid to the toxic discharge of effluent in to the sea. What was missing in all the above developments was the negligence of Nature by discharge of emissions or effluents into the Natural world. We have taken Nature for granted and treated her with great indignity and contempt. Few decades ago Scientists were able to make remarkable discoveries using only their mind as a tool and theorizing certain concepts. They were abstract in nature but were validated whenever applied in practice. There were no big investments by Governments or companies on scientific discoveries, no Intellectual property portfolios, no personal ownership, no disputes on infringement as to who owns and what. Today scientific inventions and intellectual properties are the biggest assets and monopolies of few corporate and nations.  Several hundred billions are spent on patents, trademarks and copy rights to stamp their authorities and ownerships. But where such knowledge came from? Who pays for the consequences of ill -conceived scientific discoveries that prove disastrous in the long run? Who can sue them when such technologies are passed on to several generations without knowing their long term consequences? Science is now suggesting methods to address carbon emission using various renewable energy sources such as solar, wind, biomass etc. But these methods often use capital intensive equipments to use such energy even though Nature provides them free of cost. Such equipments also require large energy input to produce which again comes from fossil fuel maintaining the level of CO2 in the atmosphere. The investment on renewable energy has come down by nearly 70% according to latest news and many countries are gearing up to step up their fossil fuel production in the name of “energy security” simply because they have become “addicted “to old ways of living. In fact there is too much at stake for these countries and they are stubbornly sticking to old ideas. Science has become useless in addressing climate change because it is no longer about science but about nation’s security and maintaining material wealth of the citizens of a particular nation and the popularity of politicians among the ignorant masses and  winning their elections and holding to their power. Sun is the only source of energy on the planet earth and all other forms of energy such as wind and biomass etc are only by-products of sun.  Current power generating technologies heavily depends of conversion of thermal energy into electrical energy and the source of thermal energy is by fossil fuel or nuclear. Recently light energy from sun is converted directly into electrical energy using photovoltaics. They also use thermal energy of the sun using solar concentrators to generate power in conventional way using turbines. But high initial cost, lack of energy storage technologies and intermittent nature of renewable sources increases the cost of energy compared to conventional coal fired power and alternative energy has created an uncertainty in the power industry. Energy industry is now at the cross road and it has divided people into two categories; one group accepts science of global warming and climate change and advocate substituting fossil fuel with carbon free energy sources and another group express skepticism over climate science and support fossil fuel energy sources in order to continue and maintain the industrial growth and employment. If countries like US and Australia who have rich deposits of high grade coal and depend heavily on coal based power plants and industries then they have an option to increase the efficiency of coal utilization by way of emission reduction. For example they can reduce carbon emission substantially using gasification technologies. In fact, under certain special conditions it is possible to generate syngas from coal with highest Hydrogen content (even up to CO: H2 ratio of 20:80).This will increase not only the calorific value of syngas but also reduce carbon emission. Companies like GE, USA are developing special gas turbines for syngas with high hydrogen content. Alternatively conversion of coal into synthetic natural gas (SNG) can reduce the carbon emission without dispensing with coal completely. Renewable hydrogen is a potential long term substitute for fossil fuel both for power industry and transportation. But it requires special handling due to its high explosive nature and it is often easier to handle it with a mix of hydrocarbon such as Methane or Carbon monoxide. Fuel cell is an emerging technology that can use hydrogen for power generation as well as for transportation. However it requires expensive catalysts and they are currently confined to smaller applications in power industry. Fuel cell opens up a new way to generate electricity by simply stripping electrons from a hydrogen atom with Platinum and allowing the resulting proton exchange by special membranes in a cell converting chemical energy into an electrical energy. It is certainly a breakthrough in power generation but there is a long way to go before commercializing them on larger scale. It seems Carbon will continue to play an important role for years to come due to its unique nature in the natural world. But high carbon intensity fuel such as coal and current methods of direct combustion will have to be abandoned and substituted with SNG or Syn gas with high hydrogen content by gasifying coal. By this way hydrogen can be introduced into the current energy mix without substantial deviation from using coal while maintaining the carbon emission well within the limit. However a long term strategy will require complete substitution of fossil fuel with renewable hydrogen or with completely a new method of electricity generation such as Fuel cell without using a thermal energy.  Electricity is nothing but a flow of electrons and techniques that are currently used in Fuel cell such as proton exchange membrane should be developed using low cost catalyst and materials on a much larger scale to substitute fossil fuel completely. It is clear that power generation technology should be delinked with using carbon source or combustion for that matter. Combustion of hydrogen electrochemically is an elegant solution but lot of research and development is required. But the stark reality is climate is already changing and the climate change is irreversible and we have to use science to adopt our lives to the changing climate in the future. We cannot capture the carbon and bury them under the earth as Nature does because Nature has not taught us how to do it in a short span of time. The impact of climate change can be minimized or averted depending upon how fast carbon emission is reduced using new technologies. Climate change is an important lesson from which the scientific community should learn how not to interfere with Nature without a complete understanding of it. Sun shine and clean air are not just for rich and powerful but to the entire humanity on the planet. Any scientific discovery should be “holistic” and compatible with Nature and easily accessible to all human beings. Solar and biomass are emerging as alternative technologies to tackle climate change but these simple and holistic solutions were in fact practiced for decades in rural India. Farmers in India feed their cattle with cellulosic fibers (polysaccharides) as a feed and use their waste in the form of “solar” dried cakes (cow dung cakes) as a fuel that has a calorific value of 2100kj (Wikipedia). They also use the waste to generate Methane by anaerobic digestion. These technologies are not new but the challenge is they should to be built on large commercial scales to meet the demand of the growing population in a holistic way. Industrialized countries are now trying to convert the same cellulose (polysaccharides) into industrial alcohol instead of converting corn starch. When plants grow by photosynthesis using sun, it generates starch, lignin, cellulose as well as fatty acids in oil seeds.  It is important to understand that Nature provides them as food for human beings and animals and not as a raw material to generate fuel or energy and that is why “holistic solutions” are the key for the survival of science and technology as well as humanity in the future.

Battery 8hrs and Hydrogen 2 months autonomy24hrs batery storage modelBattery 10hrs and Hydrogen 17hrs autonomyBattery 8hrs and Hydrogen 2 months autonomy172 hrs (one week) battery autonomyAfrica- Australia conference

Most of the renewable energy projects that are now set up around the world are grid connected with feed-in power tariff arrangement. People can generate their own electricity by solar/wind to meet their demand and supply the surplus power to the grid at an agreed power rates. They can also draw power from the grid if there is any short fall in their production of renewable energy. It is two-way traffic. There is an opportunity for people to generate revenue by sale of surplus power. It is an incentive for people to invest on renewable energy and that is why the investment on renewable energy has steadily increased over a time. But this is not the case with many developing and under developed countries. The situation is still worse in many islands where there is no centralized power generation at all or power distribution through grids. They depend on diesel generators. Even to transport diesel from mainland they have to use diesel operated boats. They have no drinking water even though they are surrounded by sea. I happened to visit a remote island in PNG few years ago and saw the plight of those people first hand. They live in absolute poverty and nobody cares to offer them a solution. Their voices are never heard and permanently drowned in the deafening roar of the sea.

The problems of supplying clean power and water to these remote islands are not only political but also technical and commercial in nature. One has to use only commercially available systems and components which are meant for a single or three-phase grid connected power supplies. Even though renewable energy sources basically generate only direct current (DC), one has to convert them into alternate current (AC) for easy distribution and to use appliances which are designed for AC operations. Isolated communities like islands can use direct current and also use DC operated appliances because they are commercially available and they are more efficient. Anyhow most of the house appliances need DC supply and AC/DC converters are commonly used for this purpose thus sacrificing efficiency in the process. They also need better storage solutions because they are not connected to the grid and they have to necessarily store power for several days. Some of these islands are connected with inefficient wind turbines backed by diesel generators. It is an absolute necessity to incorporate a long-term storage capabilities in the system if one has to offer a continuous power and clean water. If the wind velocity is not enough (during off seasons) or if there is no sun (cloudy) for days together and if there is not enough storage capacity, then all the investment made on the project will be of no use. Any half-baked solutions will not serve the real purpose.

There are also commercial problems because a well designed system will cost more, which will eventually increase the power tariff. Unless the Government subsidizes the power   sufficiently, people cannot afford to pay for their electricity or water. It requires a careful planning and community consultations to set up a ‘stand alone renewable energy projects in islands’. Governments in the pacific islands should act with great urgency because there is also a risk of inundation by sea level rising due to global warming.

We are in the process of designing a solution to provide such islands with clean power, clean drinking water and even wireless connectivity for schools so that children can get education. It may sound ambitious but it is the first step one has to take into long journey of sustainability and self-reliance by these isolated communities. There is a good possibility that such island may one day become completely independent and self-sufficient with clean power and water.

The same solution can be implemented in other countries too. Many countries have necessary infrastructure to generate and distribute power yet they suffer regular power cuts and black outs due to inefficiencies in their system.

Our proposed solution can provide uninterrupted clean power and water because the system will have long duration centralized energy storage. We have made a detailed analysis of various alternatives available for the above purpose using Homer hybrid solution software. The solution proposes a PV solar with storage solutions using battery bank as well as Fuel cell back up. The solution also proposes a long duration of storage ranging from few hours up to a fortnight .It is a standalone system with complete energy management and suitable for remote operations. The solution can also incorporate wind turbine in addition to PV solar depending upon the site and wind velocity profile.

The model is to supply clean power and drinking water for 600 families with an average 3 people in a family. The system will supply power at the rate of 1.50kwhrs/day/person (1800 x1.5 = 2700kwhrs/day) and drinking water at the rate of 200 lits/day/person (1800 x 200 lit/person= 360,000 lits/day).The power for a desalination plant will be 1980 kwhrs/day. The system is designed for a total power generation capacity of 4680Khwhrs/day.

The model is based on battery storage as well as based on Hydrogen storage with varying durations. Comparative analysis is shown in the figures.

The first window is based on PV solar with  2 months Hydrogen autonomy.

The third window is based on PV solar with battery storage 5 days and Hydrogen 17hrs autonomy.

The fourth and fifth window is based on PV solar with battery 12hrs and Hydrogen 17hrs storage autonomy with varying panel costs

The sixth window is based on PV solar with 172 hrs (one week) battery autonomy.

The resulting analysis indicates that a centralized Hydrogen storage with Fuel cell back up offers the most economical solution even though the power tariff is higher than a system with battery storage. The investment for long duration battery storage is almost double that of Hydrogen based solution. The cost can further be reduced if and when the Electrolyzers as well as Fuel cells are manufactured on mass scale. The added advantage with this system is it can also provide Hydrogen fuel for Fuel cell cars and boats substituting diesel. One day it may become a reality that these isolated islands can become completely self sufficient in terms of water, fuel and power with no greenhouse gas emissions. This solution can be replicated to all the islands all over the world.

Note:

The above system can also be installed in many developing countries in Africa which is an emerging market. An Africa-Australia Infrastructure Conference  will be held in Melbourne, Australia on 2-3 September  2013 and it will offer a platform for Australian companies to invest in Africa on infrastructural projects.

Renewable Hydrogen offers the most potential energy source of the future for the following reasons. Hydrogen has the highest heat value compared to rest of the fossil fuels such as Diesel, petrol or butane. It does not emit any greenhouse gases on combustion. It can readily be generated from water using your roof mounted solar panels. The electrical efficiency of fuel cell using Hydrogen as a fuel is more than 55% compared to 35% with diesel or petrol engine. It is an ideal fuel that can be used for CHP applications. By properly designing a system for a home, one can generate power as well as use the waste heat to heat or air-condition your home. It offers complete independence from the grid and offers complete insulation from fluctuating oil and gas prices. By installing a renewable Hydrogen facility at your home, you can not only generate Electricity for your home but also fuel your Hydrogen car. The system can be easily automated so that it can take care of your complete power need as well as your fuel requirement for your Hydrogen car. Unlike Electric cars, you can fill two cylinders of a Hydrogen car which will give a mileage of 200miles.You can also charge your electric car with Fuel cell DC power.

Renewable Hydrogen can address all the problems we are currently facing with fossil fuel using centralized power generation and distribution. It will not generate any noise or create any pollution to the environment. It does not need large amount of water. With increasing efficiency of solar panels coming into the market the cost of renewable Hydrogen power will become competitive to grid power. Unlike photovoltaic power, the excess solar power is stored in the form of Hydrogen and there is no need for deep cycle batteries and its maintenance and disposal. It is a one step solution for all the energy problems each one of us is facing. The only drawback with any renewable energy source is its intermittent nature and it can be easily addressed by building enough storage capacity for Hydrogen. Storing large amount of energy is easy compared to battery storage.

The attached ‘You Tube’ video footage show how Solar Hydrogen can be used to power your home and fuel your Hydrogen car. Individual homes and business can be specifically designed based on their power and fuel requirements.

Fuel cell technology is emerging as a base-load power generation technology as well as back-up power for intermittent renewable energy such as solar and wind, substituting conventional storage batteries. However, Fuelcell requires a Fuel in the form of Hydrogen of high purity. The advantage of Fuel cell is, its high electrical efficiency compared to conventional fossil fuel power generation technology, using Carnot cycle. Fuel cell is an electro-chemical device like a battery and generates power using electro-chemical redox reaction silently with no gaseous emission, unlike engines and turbines with combustion, rotary movements and gaseous emissions. The fuel Hydrogen can be generated using a renewable energy sources such as solar and wind as described in my previous articles, “Solar Hydrogen for cleaner future” dated 4 July 2012, and “Renewable Hydrogen for remote power supply “dated 28 June 2012.

Alternatively, Hydrogen can also be generated using biomass through Biogas. Biogas is an important source of renewable energy in the carbon constrained economy of today’s world. The biogas can be generated from waste water and agro-waste by anaerobic digestion using enzymes. Biomass such as wood waste can also be gasified to get syngas, a mixture of Hydrogen and Carbon dioxide. In anaerobic digestion, the main product will be methane gas accompanied by carbon dioxide and nitrogen while the main product in gasification will be Hydrogen, carbon monoxide and carbon dioxide and oxides of Nitrogen. Whatever may be the composition of the resulting gas mixture, our focus will be to separate methane or Hydrogen from the above mixture. In anaerobic digestion, the resulting Methane gas has to be steam reformed to get Hydrogen gas suitable for Fuel cell application. In gasification, the resulting Syngas has to be separated into pure Hydrogen and Carbon dioxide so that pure Hydrogen can be used as a fuel in Fuel cell applications. As I have outlined in many of my previous articles, Hydrogen was the only fuel we have used all these years and we are still using it  in the form of Hydrocarbons and it will continue to be the fuel in the future also. The only difference is future Hydrogen will be free from carbon.

We have to discuss two issues to mitigate Carbon emission, and it can be done by 1.Elimination of Carbon from the fuel source. 2. Generation of Renewable and Carbon free clean energy directly from solar and wind. One option  to cut Carbon from the fuel source is to use Biomass as the raw material to generate Hydrogen so that fresh Carbon will not be added  into the atmosphere by emissions .The second option is to generate pure Hydrogen from water by electrolysis using renewable energy such as wind and solar. Environmentally friendly waste-to-energy projects are becoming popular all over the world. But now most of these waste-to-energy projects generate either Biogas (Methane) by anaerobic digestion or Syngas (Hydrogen and Carbon dioxide) by gasification. Both these gases need further purification before they can be used as a fuel for power generation. The Methane content in the Biogas (about 60% methane and 40% Carbon dioxide with other impurities) needs to be enriched to 90% Methane and free from other impurities. The composition of a typical Biogas is shown in table1.

The resulting purified methane gas will be reformed using steam reformation in presence of a catalyst to get syngas; finally Hydrogen should be separated from resulting syngas so that it can be used directly into the Fuelcell.The common Fuel cell used for this application is invariably Phosphoric acid fuel cell.

PAFC uses 100% Phosphoric acid in Silicon carbide matrix as an electrolyte. PAFC is a self-contained unit completely enclosed in a cabin consisting of a gas reformer, Fuellcell power generator, Power conditioning unit and other auxiliaries. The PAFC is of modular construction with capacities ranging from 100Kw up to 500Kw as a single unit. It can be installed outdoor in the open and it can be readily connected to a piped Biogas. It can also be connected to existing piped natural gas or LPG bullet as a stand-by fuel. Any waste-to energy project can be integrated with Fuel cell power generation with CHP application to get greatest economic and environmental benefits. Hydrogen derived from biomass will be an important source of fuel in the future of clean energy; and Fuel cell will become an alternative power generation technology for both stationary power generation and transportation such as Fuel cell car or Hybrid cars.

PAFC is a compact, self-contained power generation unit that is used even for base load power. The electrical efficiency of PAFC  is about 42% .It is suitable for CHP applications so that the total energy efficiency can reach up to 85%.It is ideal for supplying continuous power 24×7 and also to use waste heat for space heating or space air-conditioning with an absorption chiller in CHP applications. The ideal candidates for PAFC power generation using CHP will be hospitals, super markets, Data centers, Universities or any continuous process industry.PAFC is now used as a backup power for large-scale renewable energy project with an access to piped natural gas. A schematic flow diagram of a fuel cell power generation is shown in Fig 3 using biogas at Yamagata sewage treatment plant in Japan. Biomass  based  Fuecell  power generation has a great potential all over the world irrespective of location and size of the country.

Batteries have become indispensable for energy storage in renewable energy systems such as solar and wind. In fact the cost of battery bank, replacements, operation and maintenance will exceed the cost of PV solar panels for off grid applications during the life cycle of 20 years. However, batteries are continued to be used by electric power utilities for the benefits of peak shaving and load leveling. Battery energy storage facilities give the dynamic benefits such as voltage and frequency regulation, load following, spinning reserve and power factor correction along with the ability to give peak power.

Fuel cell power generation is another attractive option for providing power for electric utilities and commercial buildings due to its high-efficiency and environmentally friendly nature. This type of power production is especially economical, where potential users are faced with high cost in electric power generation from coal or oil, or where environmental constraints are stringent, or where load constraints of transmission and distribution systems are so tight that their new installations are not possible. Both batteries and fuel cells have their own unique advantages to electric power systems. They also contain a great potential to back up severe PV power fluctuations under varying weather conditions.

Photovoltaic power outputs vary depending mainly upon solar insolation and cell temperature.  PV power generator may sometimes experience sharp fluctuations owing to intermittent weather conditions, which causes control problems such as load frequency control, generator voltage control and even system stability.  Therefore there is a need for backup power facilities in the PV power generation.   Fuel cells and batteries are able to respond very fast to load changes because their electricity is generated by chemical reactions. A 14.4kW lead acid battery running at 600A has greatest load gradient of 300 A/sec, a phosphoric-acid fuel cell system can match a demand that varies by more than half its rated output within 0.1 second. The dynamic response time of a 20kW solid-oxide fuel cell power plant is less than 4 second when a load increases from 1 to 100%, and it is less than 2 msec when a load decreases from 100 to 1%.  Factory assembled units provides fuel cell and battery power plants with short lead-time from planning to installation. This modular production enables them to be added in varying increments of capacity, to match the power plant capacity to expected load growth. In contrast, the installation of a single large conventional power plant may produce excess capacity for several years, especially if the load growth rate is low.  Due to their multiple parallel modular units and absence of combustion and electromechanical rotary devices, fuel cell and battery power plants are more reliable than any other forms of power generation. Fuel cells are expected to obtain performance reliability near 85%. Consequently, a utility that installs a number of fuel cell or battery power plants is able to cut its reserve margin capacity while maintaining a constant level of the system reliability. The electrochemical conversion processes of fuel cells and batteries are silent because they do not have any major rotating devices or combustion.  Water requirement for their operation is very little while conventional power plants require a massive amount of water for system cooling.

Therefore, they can eliminate water quality problems created by the conventional plants’ thermal discharges. Air pollutant emission levels of fuel cells and batteries are none or very little. Emissions of SO2 and NOx in the fuel cell power plant are 0.003 lb/MWh and 0.0004 lb/MWh respectively. Those values are projected to be about 1,000 times smaller than those of fossil-fuel power plants since fuel cells do not rely on combustion process. These environmentally friendly characteristics make it possible for those power plants to be located close to load centers in urban and suburban area. It can also cut energy losses and costs associated with transmission and distribution equipment. Their site near load centers may also cut the likelihood of power outage.

Electricity is produced in a storage battery by electro-chemical reactions. Similar chemical reactions take place in a fuel cell, but there is a difference between them with respect to fuel storage. In storage batteries chemical energy is stored in the positive/negative electrodes of the batteries. In fuel cells, however, the fuels are stored externally and need to be fed into the electrodes continuously when the fuel cells are operated to generate electricity.

Power generation in fuel cells is not limited by the Carnot Cycle in the view that they directly convert available chemical free energy to electrical energy than going through combustion processes.  Therefore fuel cell is a more efficient power conversion technology than the conventional steam-applying power generations. Fuel cell is a one-step process to generate electricity, the conventional power generator has several steps for electricity generation and each step incurs a certain amount of energy loss. Fuel cell power systems have around 40-60% efficiencies depending on the type of electrolytes. For example, the efficiencies of phosphoric-acid fuel cells and molten-carbonate fuel cells are 40-45% and 50-60%, respectively. Furthermore, the fuel cell efficiency is usually independent of size; small power plants run as efficiently as large ones. Battery power systems themselves have high energy efficiencies of nearly 80%, but their overall system efficiencies from fuel through the batteries to converted ac power are reduced to below 30%. This is due to energy losses taking place when one energy form is converted to another

A battery with a rated capacity of 200Ah battery will give less than 200 Ah. At less than 20A of discharge rates, the battery will give more that 200 Ah. The capacity of a battery is specified by their time rate of discharge. As the battery discharges, its terminal voltage, the product of the load current and the battery internal resistance gradually decreases. There is also a reduction in battery capacity with increasing rate of discharge. At 1-hr discharge rate, the available capacity is only 55% of that obtained at 20-hr rate. This is because there is insufficient time for the stronger acid to replace the weak acid inside the battery as the discharge proceeds.   For fuel cell power systems, they have equally high-efficiency at both partial and full loads. The customer’s demand for electrical energy is not always constant. So for a power utility to keep adjustment to this changing demand, either large base-load power plants must sometimes run at part load, or smaller peaking units must be used during periods of high demand. Either way, efficiency suffers or pollution increases. Fuel cell systems have a greater efficiency at full load and this high-efficiency is retained as load diminishes, so inefficient peaking generators may not be needed.

Fuel cells have an advantage over storage batteries in the respect of operational flexibility. Batteries need several hours for recharging after they are fully discharged. During discharge the batteries’ electrode materials are lost to the electrolyte, and the electrode materials can be recovered during the recharging process. Over time there is a net loss of such materials, which may be permanently lost when the battery goes through a deep discharge. The limited storage capacity of the batteries implies that it is impossible for them to run beyond several hours.

Fuel cells do not undergo such material changes. The fuel stored outside the cells can quickly be replenished, so they do not run down as long as the fuel can be supplied.   The fuel cells show higher energy density than the batteries when they run for more than 2 hours. It means that fuel cell power systems with relatively small weight and volume can produce large energy outputs. That will give the operators in central control centers for the flexibility needed for more efficient use of the capital-intensive fuel cell power plants.

In addition, where hydrogen storage is possible, renewable power sources can drive an electrolysis process to produce hydrogen gas during off-peak periods that will be used to run the fuel cells during peak demands. The usage of storage batteries in an electric utility industry is expected to increase for the purposes of load leveling at peak loads, real-time frequency control, and stabilizing transmission lines. When integrated with photovoltaic systems, the batteries are required to suppress the PV power fluctuations due to the changes of solar intensity and cell temperature. The fact that the PV power outputs change sharply under cloudy  weather conditions makes it hard to decide the capacity of the battery power plants since their discharging rates are not constant. For a lead-acid battery, the most applicable battery technology for photovoltaic applications to date, the depth of discharge should not exceed 80% because the deep discharge cycle reduces its effective lifetime. In order to prevent the deep discharge and to supplement varying the PV powers generated on cloudy weather days, the battery capacity must be large. Moreover, the large battery capacity is usually not fully used, but for only several days. Fuel cells integrated with photovoltaic systems can give smoother operation. The fuel cell system is capable of responding quickly enough to level the combined power output of the hybrid PV-fuel cell system in case of severe changes in PV power output. Such a fast time response capability allows a utility to lower its need for on-line spinning reserve. The flexibility of longer daily operation also makes it possible for the fuel cells to do more than the roles of gas-fired power plants. Gas turbines are not economical for a purpose of load following because their efficiencies become lower and operating costs get higher at less than full load conditions

Fuel cell does not emit any emission except water vapor and there is absolutely no carbon emission.  However, storage batteries themselves do not contain any environmental impacts even though the battery charging sources produce various emissions and solid wastes. When an Electrolyzer is used to generate Hydrogen on site to fuel the Fuel cell, the cost of the system comes down due to much reduction in the capacity of the battery. The specific cost of energy and NPC is lower than fully backed battery system.

During dismantling, battery power plants require a significant amount of care for their disposal to prevent toxic materials from spreading around. All batteries that are commercially viable or under development for power system applications contain hazardous and toxic materials such as lead, cadmium, sodium, sulfur, bromine, etc. Since the batteries have no salvage value and must be treated as hazardous wastes, disposal of spent batteries is an issue. Recycling batteries is encouraged and not placing them in a landfill. One method favoring recycling of spent batteries is regulation. Thermal treatment for the lead-acid and cadmium-containing batteries is needed to recover lead and cadmium. Sodium-sulfur and zinc bromine batteries are also required to be treated before disposal.

Both batteries and fuel cells are able to respond very fast to system load changes because they produce electricity by chemical reactions inside them. Their fast load-response capability can nicely support the sharp PV power variations resulted from weather changes.  However, there are subtle different attributes between batteries and fuel cells when they are applied to a PV power backup option. Power generation in fuel cell power plants is not limited by the Carnot Cycle, so they can meet high power conversion efficiency. Even taking into account the losses due to activation over potential and ohmic losses, the fuel cells still have high efficiencies from 40% to 60%. For example, efficiencies of PAFCs and MCFCs are 40-45% and 50-60% respectively. Battery power plants, however, themselves have high energy efficiency of nearly 80%, but the overall system efficiency from raw fuel through the batteries to the converted ac power is reduced to about 30%.

A battery’s terminal voltage gradually decreases as the battery discharges due to a proportional decrease of its current. A battery capacity reduces with increasing rate of discharge, so its full capacity cannot be used when it discharges at high rates. On the other hand, fuel cell power plants have equally high-efficiency at both partial and full loads. This feature allows the fuel cells to be able to follow a changing demand without losing efficiency. The limited storage capacity of batteries indicates that it is impossible for them to run beyond several hours. The batteries when fully discharged need several hours to be recharged.

For its use in PV power connections, it is as hard   to estimate the exact capacity of the batteries. In order to prevent the batteries’ deep discharge and to supplement the varying PV powers on some cloudy weather days, the battery capacity should be large, but that large capacity is not fully utilized on shiny days. For fuel cells, they do not contain such an operational time restriction as long as the fuel can be supplied. Thus, the fuel cell power plants can give operational flexibility with the operators in central control centers by utilizing them efficiently. As intermediate power generation sources, fuel cell power plants may replace coal-fired or nuclear units under forced outage or on maintenance. For the PV power backup the batteries’ discharge rate is irregular and their full capacity may usually not be consumed. So, it is difficult to design an ideal capacity of the battery systems for support of the PV power variations and to economically run them. Instead of batteries fuel cell power plants show diverse operational flexibility for either a PV power backup or a support of power system operation.

 

PV solar is expanding as a potential renewable energy source for each house, and the cost of solar panels are slowly coming down as the volume of production increases. However, the intermittent nature of solar energy is still an issue, especially for off grid and remote locations. Now solar energy is stored using lead acid batteries for such applications and inverters become part of the system. The capacity of the battery bank is designed to meet the electrical demand and to absorb the fluctuation of the energy generated by solar panels and it varies from place to place. This method stores the electrical energy generated by PV solar in the form of DC current and delivers it in the form of AC current. Though this method is the simplest one for remote locations, storing solar power in the form of Hydrogen is more economical and environmentally friendly in the long run.

Solar energy can directly be used to generate Hydrogen using solid polymer electrolyzers and stored in cyclinders.The stored Hydrogen can then be used to fuel a stationary Fuel cell to generate power on site. One can design a system by integrating various components in such a way; the Hydrogen generated by solar energy is used to generate power on site as and when required. By this method one can generate required power throughout the day 24×7 irrespective of the availability of sun. The system integration involves various components supplied by various manufacturers with various specifications and the success of a system depends on the careful design using data acquired over a time on a specific location.

Many winds to Hydrogen projects also have been tested in locations around the world.NREL (National renewable energy laboratory, USA) has conducted number of tests by integrating various components such as PV solar and wind turbines with Electrolyzers (both PEM electroylzers and alkaline electrolyzers) and Hydrogen IC engines for remote power generation as well as for fuelling vehicles with Hydrogen. Though the cost of this system is still expensive, such integration offers enormous potential as a clean energy source for remote locations without any grid power. When one takes into account the fluctuating oil prices, cost of global warming, cost of power transmissions and losses during long distance power transmission from fossil fuel power plants, Renewable Hydrogen offers the best and sustainable alternative to fossil fuels. Such a system offers complete independence, energy security, reliability and fixed power tariff.

System integration of renewable energy sources for Hydrogen production and on site power generation using Fuel cell or Hydrogen engine is the key to a successful deployment of solar and wind energy for rural electrification and to remote islands. Such system will offer greater return on investment even to supply power to the grid based on power purchase agreements with Government and private companies. Renewable Hydrogen is the only practical solution for clean power of the future and sooner we embrace this integrated solution better for a cleaner future. Government and private companies investing on oil and gas explorations can focus their attention in developing renewable Hydrogen based solutions so that the cost of Hydrogen can become competitive to fossil fuel. Once the cost of Hydrogen reaches parity with cost of fossil fuel then, it will set the beginning of a green revolution in clean energy.

Wind energy is one of the fastest growing renewable energy sources in the world and in 2011 the global market grew by 6% with 40.5 GW new powers brought online, according to Global Wind Report. However storage of intermittent renewable energy is a critical contributing factor in renewable energy development. A study was conducted by University of California for California Energy Commission on the economic and environmental impact of for energy storage technologies and the ways to improve the energy efficiency of wind energy. When there is a strong wind there is no demand for power, and when there is a high demand for power there is no wind. This anomalous supply demand gap demands a reliable way of storing wind power during high wind velocity periods.

They examined for energy storage technologies namely 1.lead acid batteries, 2. Zinc Bromine flow batteries, 3.Hydrogen electrolyzer and Fuel cell storage system and 4.Hydrogen option to fuel Hydrogen cars with Hydrogen. By using NREL (national Renewable Energy laboratory) computer simulation model HOMER  for high wind penetration of 18% in California, they concluded that Hydrogen storage is the most cost-effective than other battery storage technologies and using Hydrogen to fuel Hydrogen cars is economically attractive  than converting Hydrogen into Electricity. The environmental impact of using Hydrogen is benign compared to batteries with their emissions.

“The key findings of this experiments are as follows: Energy storage systems deployed in the context of greater wind power development were not particularly well used (based on the availability of “excess” off-peak electricity from wind power), especially in the 2010 time frame (which assumed 10% wind penetration statewide), but were better utilized–up to 1,600 hours of operation per year in some cases–with the greater (20%) wind penetration levels assumed for 2020.

The levelized costs of electricity from these energy storage systems ranged from a low of $0.41 per kWh—or near the marginal cost of generation during peak demand times—to many dollars per kWh (in cases where the storage was not well utilized). This suggests that in order for these systems to be economically attractive, it may be necessary to optimize their output to coincide with peak demand periods, and to identify additional, value streams from their use (e.g., transmission and distribution system optimization, provision of power quality and grid ancillary services, etc.).

At low levels of wind penetration (1%–2%), the electrolyzer/fuel cell system was either inoperable or uneconomical (i.e., either no electricity was supplied by the energy storage system or the electricity provided carried a high cost per MWh).

In the 2010 scenarios, the flow battery system delivered the lowest cost per energy stored and delivered.  At higher levels of wind penetration, the hydrogen storage systems became more economical such that with the wind penetration levels in 2020 (18% from Southern California), the hydrogen systems delivered the least costly energy storage.

Projected decreases in capital costs and maintenance requirements along with a more durable fuel cell allowed the electrolyzer/fuel cell to gain a significant cost advantage over the battery systems in 2020.

Sizing the electrolyzer/fuel cell system to match the flow battery system’s relatively high instantaneous power output was found to increase the competitiveness of this system in low energy storage scenarios (2010 and Northern California in 2020), but in scenarios with higher levels of energy storage (Southern California in 2020), the electrolyzer/fuel cell system sized to match the flow battery output became less competitive.

The hydrogen production case was more economical than the electrolyzer/fuel cell case with the same amount of electricity consumed (i.e., hydrogen production delivered greater revenue from hydrogen sales than the electrolyzer/fuel cell avoided the cost of electricity, once the process efficiencies are considered).

Furthermore, the hydrogen production system with a higher-capacity power converter and electrolyzer (sized to match the flow battery converter) was more cost-effective than the lower-capacity system that was sized to match the output of the solid-state battery. This is due to economies of scale found to produce lower-cost hydrogen in all cases.

In general, the energy storage systems themselves are fairly benign from an environmental perspective, with the exception of emissions from the manufacture of certain components (such as nickel, lead, cadmium, and vanadium for batteries). This is particularly true outside of the U.S., where battery plant emissions are less tightly controlled and potential contamination from improper disposal of these and other materials is more likely. The overall value proposition for energy storage systems used in conjunction with intermittent renewable energy systems depends on diverse factors:

The interaction of generation and storage system characteristics and grid and energy resource conditions at a particular site The potential use of energy storage for multiple purposes in addition to improving the dependability of intermittent renewable (e.g., peak/off-peak power price arbitrage, helping to optimize the transmission and distribution infrastructure, load-leveling the grid in general, helping to mitigate power quality issues, etc.)

The degree of future progress in improving forecasting techniques and reducing prediction errors for intermittent.  Electricity market design and rules for compensating renewable energy systems for their output”. Hydrogen storage and Hydrogen cars hold the key for future renewable energy industries and Governments and industries should focus on these two key segments.

The first few hydrogen atom electron orbitals ...

The first few hydrogen atom electron orbitals shown as cross-sections with color-coded probability density (Photo credit: Wikipedia)

Hydrogen is well-known as a potential source of clean energy of the future. But it is not available in a free form; its generation from   water using Electrolysis requires more energy than, a free Hydrogen can generate.  It requires about 5kws power to generate 1 m3 Hydrogen gas, which means, it requires about 56 Kw power to generate 1 Kg Hydrogen using water electrolysis. But 1Kg Hydrogen can generate only about 15-20 Kw Electricity using a Fuel cell. This anomalous situation makes Hydrogen generation using water electrolysis uneconomical for clean power generation. That is why most of the Hydrogen is now generated by steam reforming natural gas. Another reason for using natural gas is, to cut the cost of Hydrogen and also, to make a smooth transition from fossil economy to Hydrogen economy using existing infrastructures. Power generation and transportation using Hydrogen and Fuel cell has been commercially tested, proven and ready for deployment. However, we still have to deal with emission of greenhouse gas during steam reformation of natural gas due to the presence of carbon atom in natural gas.

Meanwhile, one American company recently announced a break-through technology that will generate free thermal energy from atomic Hydrogen using a patented process. The inventor of the process claims, when atomic Hydrogen is allowed to react with a specific Catalyst, Hydrogen atom undergoes a transition to a new atom called “Hydrino”, releasing energy while the electron in the atom shifts to a lower orbit close to proton. It was believed so far that the electron in Hydrogen atom is at its lowest level (ground level) and the closest to proton. This is the first time somebody claims that there is a lower state than the ground state  in Hydrogen atom and the amount of energy released in this transition to ‘Hydrino”,  is  in between by an uncatalyzed Hydrogen atom by combustion and nuclear energy. Unlike nuclear energy, this energy is non-radioactive. But the energy released by this process is more than 200 times than energy released by Hydrogen atom by normal combustion. The reaction does not create any pollution or radio-active materials as by-products. The process has been tested, verified and certified by scientists in few  laboratories and universities.

The above process offers great hope to generate a clean, non-polluting energy at the lowest cost. The ‘dihydrino and Hydrogen is separated and Hydrogen is recycled back to continue the process while’dihydrino’ has other potential commercial applications. The inventor has named this power as “Black power” as he hypotheses that such phenomena explain the presence of “dark matter” in Galaxies. According to quantum mechanics, the energy level of a normal Hydrogen atom is at its ground level as its minimum level (N=1), but its energy level increases at higher states such as N=2, 3, 4.When the energy level jumps from higher (excited state) to a lower level, it emits energy in the form of photon of light (Quanta).The spectrum of such emission matches the ultraviolet light of the sun. Since sub-quantum atoms are non-radioactive, the inventor claims that he is duplicating the above process of Nature by a catalytic thermal process in the state of Plasma using a specific Catalyst.

If such a large thermal energy is released by formation of ‘Hydrino’atom in the above process, then such energy can be used to generate Hydrogen by conventional water electrolysis at a fraction of the cost.

Then, Hydrogen economy can become a commercial reality and the above technology has a potential not only to generate power at fraction of a cost of the fossil fuel but also to generate a clean and non-polluting power. The inventor has also hypothesised a “grand new unified theory” of atom as the basis for the above invention. Mainstream scientists have always have been reluctant to support such “free energy” theories but, when someone can prove the process of generating an excess energy (more than 200 times than the theoretical energy released by an exothermic chemical reaction) and it is non-radioactive then mainstream scientists may be sidelined by world community. It is always possible to prove something unique without any theory   and come out later with a theoretical explanation to satisfy the scientific community. Many discoveries in the past were by mere accidents and one should have an open mind to look into any new concepts without any bias, especially if the discovery can resolve serious problems of humanity at  times  of crisis.

 

We now generate electric city from heat, obtained by combustion of fossil fuel such as coal, oil and gas. But such combustion generates not only heat but also greenhouse gases such as Carbon dioxide and oxides of Nirogen.The only alternative to generate power without any greenhouse gas emission is to use a fuel with zero carbon. However, oxides of Nitrogen will still be an issue as long as we use air for combustion because atmospheric air has almost 79% Nitrogen and 21% oxygen. Therefore it becomes necessary to use an alternative fuel as well as an alternative power generation technology in the future to mitigate greenhouse problems.

Hydrogen is an ideal fuel to mitigate greenhouse gases because combustion of Hydrogen with oxygen from air generates only water that is recyclable. Combining Hydrogen with Oxygen using Fuel cell, an electrochemical device is certainly an elegant solution to address greenhouse problems. But why Hydrogen and Fuel cell are not commonly available? Hydrogen is not available freely even though it is abundantly available in nature. It is available as a compound such as water (H2O) or Methane (CH4) and Ammonia (NH3). First we have to isolate Hydrogen from this compound as free Hydrogen and then store it under pressure. Hydrogen can easily form an explosive mixture with Oxygen and it requires careful handling. Moreover it is a very light gas and can easily escape. It has to be compressed and stored under high pressure.

Generation of pure Hydrogen from water using Electrolysis requires more electricity that it can generate. However, Hydrogen cost can be reduced using renewable energy source such as solar thermal. The solar thermal can also supply thermal energy for decomposing Ammonia into Hydrogen and Nitrogen as well as to supply endothermic heat necessary for steam reformation of natural gas into Hydrogen. On-site Hydrogen generation using solar thermal using either electricity or heat can become a commercial reality. Hydrogen generation at higher temperatures such as Ammonia decomposition or steam reformation can be directly used in Fuel cell such as Phosphoric acid Fuel cell.

Phosphoric acid fuel cell is a proven and tested commercial Fuel cell that is used for base load power generation. It is also used for CHP applications. Hydrogen generation using solar thermal and power generation using Fuel cell is already a commercial reality and also an elegant solution to mitigate greenhouse gases. Large scale deployment of Fuel cell and solar thermal will also cut the cost of installations and running cost competing with fossil fuel.Fuecell technology has a potential to become a common solution for both power generation and transportation.

While Government can encourage renewable energy by subsidizing PV solar panels and discourage fossil fuel by imposing carbon tax, they should give preference and higher tariff for power purchase from Solar thermal and Fuel cell power generators. This will encourage large-scale deployment of Fuel cell as a potential base load power source.

%d bloggers like this: